全自動涼茬機是能酒茬攤涼攪拌后，加入酒曲混合的設備。工作時間短、非常節約資源、自動加曲卸料、減輕了工人們的勞動強度，還杜絕了浪費糧食的現象。下面來講講全自動涼茬機電機使用前的檢查方法。
The automatic stubble cooler is a device that can add distiller's yeast after the liquor stubble is cooled and stirred. Short working hours, very resource saving, automatic bending and unloading, reduce the labor intensity of workers, but also put an end to the phenomenon of food waste. Now let's talk about the inspection method of the motor of the automatic stubble cooler before use.
1、用壓縮空氣或手動吹風機吹凈電動機內部灰塵、電刷粉末等，污垢雜物。
1. Use compressed air or manual blower to blow out the dust, brush powder, etc. inside the motor to remove dirt and debris.
2、拆除與電動機連接的一切接線，用絕緣電阻表測量繞組對機座的絕緣電阻。若小于0．5MΩ時，應進行烘干處理，測量合格后再將拆除的接線恢復。
2. Remove all wiring connected to the motor, and measure the insulation resistance of the winding to the base with an insulation resistance meter. If it is less than 0.5M Ω, it shall be dried, and the removed wiring shall be restored after the measurement is qualified.
3、檢查涼全自動涼茬機換向器的表面是否光潔，如發現有機械損傷或火花灼痕應進行必要的處理。
3. Check whether the surface of the commutator of the fully automatic stubble cooler is smooth and clean. If any mechanical damage or spark burn is found, necessary treatment shall be carried out.
4、檢查電刷是否嚴重損壞，刷架的壓力是否適當，刷架的位置是否位于標記的位置。
4. Check whether the brush is seriously damaged, whether the pressure of the brush holder is appropriate, and whether the position of the brush holder is at the marked position.
使用時，酒茬在傳送帶上通過，在打碎和攪拌的同時風機工作，迅速降溫，冷卻后的酒茬在下料裝置中與酒曲自動混合均勻。本實用新型全自動涼茬機提高了冷卻效果、降低了功耗，了現有設備自積堵塞現象，并實現了酒茬和酒曲的自動混合。
When in use, the wine stubble passes on the conveyor belt, and the fan works while breaking and stirring to quickly cool down. The cooled wine stubble is automatically mixed with the starter in the blanking device. The full-automatic stubble cooler of the utility model improves the cooling effect, reduces the power consumption, solves the self accumulation blockage of existing equipment, and realizes the automatic mixing of wine stubble and distiller's yeast.
在啟動全自動涼茬機之前，我們應當先檢查機器的電機是否正常，再去啟動設備。在檢查時，應同時使用吹風機對電機內的灰塵等污垢雜物清理干凈，還要測量接線是否合格，如果發現電機出現機械損傷或者火花灼痕應當立即進行必要的處理工作。
Before starting the automatic stubble cooler, we should first check whether the motor of the machine is normal, and then start the equipment. During the inspection, the blower shall be used to clean the dust and other dirt and sundries in the motor, and the wiring shall be measured to see whether it is qualified. If the motor is found to have mechanical damage or spark burns, necessary treatment shall be carried out immediately.
根據全自動涼茬機電動機銘牌檢查直流電動機各繞組之間的接線方式是否正確，電動機額定電壓與電源電壓是否相符，電動機的起動設備是否符合要求，是否完好無損。更多相關注意事項就來我們網站
http://kadai88.com咨詢！
According to the nameplate of the fully automatic stubble cooler motor, check whether the wiring mode between the windings of the DC motor is correct, whether the rated voltage of the motor is consistent with the power voltage, and whether the starting equipment of the motor meets the requirements and is intact. More relevant precautions come to our website http://kadai88.com consulting service
自動售酒機 2024-07-25 
